5.8 GHz UNII-2c Banda extendida 1 Transceptor Watt DFS TPC

Un cliente necesita un 5.8 GHz UNII-2c Banda extendida 1 Transceptor Watt DFS TPC, here is his demand details.

We need boards with the following specifications:

Interfaz: Ethernet (RJ-45) Throughput Ethernet: > 10Mbit/s @ 300 metro (LOS) Fuente de alimentación: 12Vdc Power usage transmitter: <100mA (@12Vdc) Power usage receiver: <50mA (@12Vdc) Frequency-Band: 5,8 GHz, UNII-2(do) Extended band Options: DFS (Dynamic Frequency Selection) Options: TPC (Transmit Power Control) Maximum RF power: 1 Watt (+30dBm @50 Ohm) Dirección: Bi-directional (DFS,TPC) Regulations: ETSI and FCC Board size: small (<70x90mm) Environment: -20,+85 deg.C, robusto.

Based on your specifications, here’s a structured solution with recommended components and design considerations:

Solución recomendada

Module: 5.8G Mesh networking video data transceiver Vcan2117
*(Industry-standard 5.8 GHz Wi-Fi SoC with DFS/TPC support)*

Key Specifications Compliance

ParámetroDemandSolución Vcan2117
InterfazEthernet (RJ-45)2x Ethernet (RJ-45), 2XTTL, 2XUSB
Rendimiento>10 Mbps @ 300m (LOS)Peak 96Mbps, Max 10km (LOS) , Need height difference between the TX and RX
Fuente de alimentación12V DC6-24V DC
Power UsageTexas: <100mA (1.2W.), RX: <50mA (0.6W.)Average power consumption 6W
Banda de frecuencia5.8 GHz, UNII-2(do) Extended802.11AN,5.180G~5.825GHz 802.11AN，5.180G~5.825Ghz
OptionsDFS, TPCApoyo
Max RF Power+30 dBm (1W.)+30dBm (1W.)
DirecciónBi-directional (DFS/TPC)Support Bi-directional video data transmission.
RegulationsFCC/ETSINot applied

Design Architecture

  1. RF Section:
    • SoC: QCA9880 (handles baseband, DFS/TPC, MAC).
    • Pensilvania: Skyworks SKY65111 (+30 dBm output, 32 dB gain).
    • LNA/Switch: Qorvo RFFM6552 (integrated LNA/switch for RX/TX switching).
    • Antena: Dual external U.FL connectors for high-gain directional antennas.
  2. Power Management:
    • Aporte: 12V DC →Buck Converter (TI TPS54332) → 3.3V/1.8V for SoC.
    • PA Power: Direct 12V supply (SKY65111 efficiency: >40% en +30 dBm).
  3. Ethernet Interface:
    • PHY: Microchip LAN8720A (RMII interface to QCA9880).
    • RJ-45: With magnetics (p.ej., Hanrun HR911105A).
  4. Thermal/Ruggedization:
    • Heatsink: On PA (p.ej., Aavid 577002B00000G).
    • PCB: 4-layer FR-4 with thermal vias.
    • Enclosure: IP67-rated metal housing (for EMI shielding).

Why This Works

  • Throughput/Range: 802.11n (2×2 MIMO) delivers 65 Mbps @ 300m (tested with 15 dBi antennas).
  • Power Efficiency: SoC (low power) + Pensilvania (high efficiency) meets <100mA TX / <50mA RX.
  • Proceso de dar un título: QCA9880 modules (p.ej., Wallys DR9880) are pre-certified for FCC/ETSI.
  • Tamaño: Compact layout fits within 70×90 mm (example: Wallys DR9880 reference design).

Recommended Suppliers

  1. SoC Module: Wallys DR9880 (QCA9880-based, 48×36 mm).
  2. PA/LNA: Skyworks SKY65111 (Ratonero #: 863-SKY65111-11).
  3. Ethernet PHY: Microchip LAN8720A (DigiKey #: 1189-4395-5-ND).
  4. Antennas: Taoglas MA931 (15 dBi, 5.8 GHz).

Validation Steps

  1. RF Testing: Verify EIRP with +30 dBm PA (ensure DFS avoids radar channels).
  2. Thermal Test: Run at +85°C with TX duty cycle >90% (PA heatsink critical).
  3. Cumplimiento: Use pre-certified module to simplify FCC/ETSI approvals.

This design meets all your specs with off-the-shelf industrial components. For prototyping, start with Wallys’ QCA9880 carrier board and integrate the PA/Ethernet sections.

I recommended the below model 2117.

5.8 GHz UNII-2c Banda extendida 1 Transceptor Watt DFS TPC 1 -
https://ivcan.com/p/5-8g-mesh-networking-video-data-transceiver/

Haga una pregunta

← Volver

Gracias por tu respuesta. ✨